Seesii 電動インパクトドライバーブラシレスモーター採用 無段変速・正逆転両用LEDライト付き

【1】

DIYで木工作業中心に使ってます。トルク十分で、なんの不満もありません。

【2】

ヤッパリ３００ニュートンはトルクがありトリガーで調整できて良きかな

【3】

一年弱でバッテリー1個充電できなくなりました、もう返品はできない様です、それなりの商品ですね、本体は動いているので星3.ご参考に

【4】

とても良い品物、パワーがある、温まると止まるの、充電に時間が かかる、ちょっとした時に使うのには良い

【5】

良かった点はＢＯＸが立派な事ぐらいかな無駄なスペースがあるようにも感じるけど。まずトルクに関してはまぁ可も無く不可も無くって感じですかね。安価なのでまぁこんな所かなと思うぐらいです。

【6】

軸がぶれてる

【7】

ケースの形状と製品やバッテリーの形状が合ってないので、中身が暴れたようで傷だらけ。梱包が悪すぎる。

【8】

良かったです

【9】

This works great and lot of power and I like you can turn the power down so my grandkids can use them and I can tech them alot easier with the power turned down it don't scary them and that's awsome.And it's light weight and alot of power.

【10】

Buen destornillador y buena batería duradera y fuerza. Excelente estoy muy contento con el

【11】

This overheats quickly when used for masonry or metal using larger bits. use for wood only - buying a corded cause cordless just does not have the power.

【12】

Muy buenos lo recomiendo

【13】

I am quite favorably impressed with this impact screwdriver. In the past, using constant-rotation drill/drivers to drive screws, I’ve repeatedly had problems with driver bits slipping in screw heads at some stage of the screw penetration — damaging both the screw heads and the driver bits, no matter how slowly or carefully I tried to avoid it. In fact, I’ve often needed to coat screws with soap to be able to seat them properly; otherwise, the rotational friction between the screw and the wood was too great.This Seesii impact screwdriver appears to completely avoid these problems and, as well, drives screws quite quickly and powerfully. The photo shows three screws driven with this tool:• Previously, I had repeatedly experienced problems with other samples of the specific 2 ½ inch long, zinc-plated, # 8 screw shown at right — both using a standard constant-speed drill/driver and using a DeWalt electric deck screwdriver. In these tools, Phillips bits almost always slipped in and caused gouging of the Phillips slot, damaging the Phillips bits in the process — even when the screw had only penetrated the wood by half inch or three quarters of an inch. However, using this Seesii impact driver I have driven the same (pictured) screw three times through +different+ pieces of 2 inch lumber. Each time, all 2 ½ inches of the screw penetrated the wood quite quickly, leaving the Phillips screw head still quite usable and not damaging the driver bit at all. I’m quite impressed!• Note in the middle of the photo that a 4 inch long, #10, drywall screw completely and quickly penetrated 2 inch lumber without a hitch and without pre-drilling a pilot hole or using any kind of lubricant. (The top of the screw head cannot be driven flush with the surface of the wood, because the last 1-5/8 inches of this long screw has no threads with which to draw it flush.)• Note that, at left in the photo, a quarter inch lag bolt completely and quickly penetrated through 2 inch lumber — again, with no pre-drilled pilot hole or lubrication. The lag screw is driven in quite tightly: I cannot rotate the washer, even with a pair of Channel-Lock pliersNote that in all three cases, the wood did not split, even though I drilled no pilot holes. Might the rapid screw penetration using this impact screwdriver reduce the chance of splitting?Though this heavy-duty impact screwdriver is heavier than lighter-duty tools, it’s quite well-balanced when the battery pack is attached. Moreover, I’m delighted to have two 4 A-hr battery packs, which likely will deliver more than enough power for any job I might tackle.