Hyper PLA ABS Creality (クレアリティ) PLAフィラメント 1.75mm PLA 3Dプリンターフィラメント

【1】

3Dプリンターを箱あり型と箱無し型の2台所有していますが、PLAに比べてかなり反りやすいので箱あり型でしかうまくいきません。しっかり調整すればきれいな作品ができました。ホワイトですが、薄くすれば光は通すので、リトファンにも使えました。

【2】

他のＰＬＡ素材よりも側面の仕上がりが非常に良い。積層面での割れも全くなくしなやかに割れる事なく曲がる。スライスのモードが低レベルでも側面の仕上がりはとても良い。

【3】

結論から言うと、大満足です。まず驚いたのはその高速印刷性能。設定次第で600mm/sのスピードでもノズル詰まりや積層乱れがなく、驚くほどスムーズに造形できます。K1シリーズのような高速プリンタのポテンシャルをしっかり引き出してくれるフィラメントだと感じました。また、寸法精度±0.03mmというだけあって、全体的に造形精度も非常に高く、細かいパーツやギアなども問題なく印刷できます。サポート材の剥がれもよく、後処理がかなり楽になりました。造形中の糸引きも少なく、見た目にも非常にきれいに仕上がるのもポイントが高いです。色味も写真どおりの鮮やかなグリーンで、マットな質感が高級感を出してくれます。子供のおもちゃやインテリア雑貨の出力にも向いており、我が家では子供用のフィギュアや恐竜模型などを印刷して楽しんでいます。そして何より、ノズルトラブルが少ないというのは非常に助かります。他社のPLAフィラメントでは、たまに詰まりが起きたり、ラフトがうまく定着しなかったりすることがありますが、このHyper PLAはベッドへの密着性も優れており、1層目から安定して出力できます。価格も品質を考えれば妥当で、コストパフォーマンスは非常に高いと感じました。今後も色違いでリピートしていく予定です。Crealityユーザーであれば、間違いなく満足できる製品だと思います。

【4】

イイですね

【5】

初めての製品ですが問題無く使えました

【6】

メディアを読み込めませんでした。同社のender3 v3に合わせて、折角の焼入れノズルと思い最初に購入しました。動画は一番最初に印刷したスクレーパーです。純正ということもあって初期からぴったりのプロファイルがあり、最初のステップにぴったりでした！

【7】

安いフィラメントなのになめらかで失敗しません

【8】

絡まります。リピなし。５時間作業の出力に２時間後とかに絡まるので、完成せず。時間を返していただきたいです。

【9】

The slow start is the confusion around things like the calibration card (any sheet of paper will do, there is nothing special about this) pull the resin tank, drop the paper on the screen and then loosen the head screws on the build plate so that it's all wobbly. Drop it on the paper or the calibration card/paper and then tighten them all up. Ready to go.Replace the resin tank, fill it the max fill lines aren't easy to see so be careful. Filling past the first level can be done but use too much and you will have resin pouring everywhere. So, I would just fill to the first level on your first go. I didn't need anywhere near that amount for the thee 32 mm minis I had it punch out. 3.5 hours later they were perfect. Cleaned and UV processed them and I was quite happy with the results. Just made my Bambu Labs A1 (even on 0.2mm quality) pale in comparison to how sturdy they were. I would argue that a 5 hour filament print at 0.2mm mega quality might have produced a better print ... maybe but These three minis failed to complete without issues on THREE prints on the bambu A1. They came out beyond expectation on this as a first test print.I used water to wash em (water washable) in a tupperware container with water just swished em around (nothing fancy) and tossed em on a acrylic / resin nail curing (double sided, 20 bucks) on the middle clear plate and they cured up nicely.I am dinging the printer (i put it back up to 5 starts because the printer is fine, I just can't read Chinese lol...) for the fact that the installation manual is 2 pages of ambiguous trash. The online video (and the one on the flash drive is fine) is functional but if you didn't come across it right away you might be pulling your hair out (i had watched it before I bought this, but it's a different thing when you're doing the steps because you don't want to bust the printer). The slicing software is Creality Box, it's fine... Problem is it has no way to install it in ENGLISH or any other language for that matter. Installs in Chinese, you have to do a google search to find the character set (last on right from top left; I think it's the last option on that drill down menu for english) that allows you to change the Language. After that with a bit of toying around I knew how to do basic stuff in the slicer. Not as pretty as the Bambu slicer but it works. Can't speak to the Other license you can use for 3 months. I am using the free one and It find it ok to work with. In some ways, it's better than Bambu's because once you get the hang of it, the controls seem more intuitive (though they appear lackluster initially).CLEANUP FYI - Please have purchased plastic shelf liner or silicon mats and work on them prior to starting. Even with that, I put down a plastic kitchen garbage bag and worked on it. resin is messy and even if you're careful it will still get everywhere especially from the build plate and models you print.Cleanup, fold a piece of paper and place it half in the resin bin. Run the cleaning cycle. Pull the paper (should pull a resin film that was on the bed with it). Use the plastic scraper to get any residual stuff, pout the rest into a funnel into your resin bottle. The provided funnels suck, do some research and get a better one. I picked up a well rated Sovol metal one with strainer for like 7 bucks.I'm a total newbie but I was impressed by the speed, quality and the build area being bigger than expected. Gonna do some more prints tonight!

【10】

I recently got my hands on the Creality Hyper PLA Filament Bundle (White & Black, 2KG), and I am incredibly impressed! As an owner of an Ender 3 V3, I'm always looking for filaments that can keep up with its speed, and this Hyper PLA truly delivers.The claim of 30-600mm/s print speed is not just marketing – this filament performs exceptionally well at higher speeds without sacrificing quality. I've been running my Ender 3 V3 faster than ever, and the prints come out beautifully smooth, with excellent layer adhesion. The dimensional accuracy of ± 0.03 mm is also spot-on, ensuring consistent extrusion and reliable results every time.Both the white and black colours look fantastic and provide a clean, professional finish. The filament feeds smoothly, with no tangles or clogs, which is crucial for long, high-speed prints. It's clear this PLA is designed for precision and efficiency. If you have a high-speed printer like the Ender 3 V3 or similar models, this Hyper PLA is an absolute must-buy. It genuinely elevates the printing experience. Highly recommended!

【11】

Bon rapport Qualité/Prix

【12】

Ich nutze das Creality PETG schon länger. Ich hatte es mir mal für ein Druck gekauft, der extrem viel Material brauchte. Da wollte ich kein teures Filament für verschwenden. Aber was soll ich sagen? Die Druckqualität ist Hervorragend! Egal ob bei dem Weißen oder Schwarzen PETG.Nur sollte man vor dem ersten Druck das Filament ordentlich trocknen, was aber bei vielen/den Meisten leider der Fall ist. Wenns um normales PETG geht, nehme ich nur noch das Creality Zeug!

【13】

Après avoir testé différente marque d'ABS, je ne peux qu'être positif avec cet ABS.pas de colle, pas de laque, un plateau bien nettoyé au liquide vaisselle, impression nickel dans un caisson fermé.Facilité d'utilisation, pas d'odeur, impression plus rapide qu'avec d'autre abs. Filament super bien enroulé !du coup je ne commande que cette marque !mise à jour au après 15 jours d'utilisation. Filament qui tient ces promesse, prévoir de l'installer dans un séchoir afin de toujours réguler l'humidité c'est la base ! Je confirme que je ne reviendrais plus jamais à d'autre marque surtout pour l'abs ! Je viens de commandé le blanc et c'est nickel également ! le terme hyper n'est pas une arnaque, pour ceux qui ont un problème a l'impression soit ils sont tombé dans une mauvaise série ou que les réglages, l'entretien de l'imprimante 3d laisse à désiré. moi après chaque sessions d'impressions j'effectue un bon nettoyage et nivellement si besoins