3018 cnc machine

【1】

製品自体非常によくでできおり、精度も申し分ないです。残念なことに緊急停止が作動せず、サポートと何回かやり取りを行いました。返信は早かったです。写真や動画は送らないといけませんでしたが・・・基板不良でなく、ボタンスイッチの初期故障だった模様です。無事届き運用しています。

【2】

素晴らしいマシーンで満足しております、只、stopスイッチを取り付ける箇所が説明書とは違っていますので注意が必要です。stopスイッチをつけないと電源が入りません、他の箇所は問題なく使えます。特にX軸側にリニアガイトが使われているので剛性がありますし、作業台は押し出し材ではなく10mmのアルミ材が使われていますのでモーターの振動がほぼありません。購入をお勧めします。500wのモーターもうるさくなく使えます。

【3】

価格通りよりやや上を行くグレードです。Gコードさえ読ませれば独自で動いてくれるコントローラーもついていて、Ｚ軸原点を取ってくれるセンサー付き、CandleでＰＣからも操作可能。星1つだけマイナスの理由は、緊急停止ボタンを解除しても解除にならない。前回押したまま忘れている場合、次回に緊急停止ボタンを押しても作動しない。必ず立ち上げ時に緊急停止ボタンが活きる様セット確認をする必要があります。後はX軸モーターに取り付けられているネジがややショボいです。このネジが破損した場合致命的です。何年持つだろうか…と言う心配があります。

【4】

商品自体がっちりしていて長く使えそうです。また、組み立ても簡単で2時間もあれば組み立て可能でした。分からないことがあったので直接サポートにメールしたさいも丁寧な対応でとても好感が持てます。安心して購入出来ると思います。

【5】

筐体もしっかりしているし、値段も安い。

【6】

メディアを読み込めませんでした。商品に不具合があって、色々良い話しをしてきますが、全て嘘でした。ここの商品も当たり外れはあるとは思いますが、自分達が言って来た事すらも言ってないかのように、態度悪く煽ってくるようなサポートです。まぁ、商品はスクラップとして出してしまった後なので返品も返金も出来なくなりましたが、嘘で騙されてしまいました。買うなら、覚悟して買った方が良いです。

【7】

パーツ不足がありました。不足しているパーツのみの発注はできません。返品による交換は可能です。組み立てを進めた後の為、迷いましたがパーツを購入することにしました。これから買われる方は先に全部入ってるか確認することをお勧めします。

【8】

メディアを読み込めませんでした。鉄の金折れを切削しました。動画のエンドミルは別で購入したものです。jw_cadで作図、NCVCでgコード出力、candleで駆動、制御。被切削物を確実に固定するのが難しい。薄型のバイスを導入したいと思っています。非常停止ボタンはｇコードの区切りまでは止まらないのは不満です。コントローラーも外さないといけないのは不便で、ホームボタンやＺ軸原点出し、各軸リミットのリセットもコントローラーに欲しい。さらに各軸の移動スピードも指定できればそれだけでそれなりの加工ができそう。今後に期待したい。ただ、初めてのＮＣフライスで大満足。良い製品なのは間違いないと思います。

【9】

er is geen software bij om iets te maken, die moet je apart kopen, alleen software om iets naar de cnc te sturen en dan nog zeer beperktetoestel zelf is wel goed en degelijk

【10】

Emballage au top, très bien protégé.Le montage s'est fait en 30mn environ. Rien de compliqué. Notice en Français pour le montage.Par contre le logiciel est en anglais. Il y a un pdf en anglais pour l'installation du logiciel mais vous pouvez le traduire avec googletraduction.La machine semble de bonne qualité. Vous pouvez anticiper en acheter un lot de fraises pour cnc cat celles fournies sont toutes identiques et uniquement destiné au bois.

【11】

One of the best machine out of the box! This is a heavy CNC and is a quality build, it came packaged very well with great care. The CNC machine went together Easily using the pictorial assembly manual i would be confident any skill level could put this together. If you have some experience with CNC routers you will not have any problems using this machine. Everything comes supplied on a USB thumb drive including the Candle software for sending the G-code files to the machine.For the newbies there is excellent videos to learn about cnc so utube it up.First thing I did after assembly and powering up the machine was to manually trigger each of the X,Y,Z home/limit switches. And it ran flawlessly I'm extremely happy with this compact unit.Will cut numerous materials with great detail the package included multiple quality bits to get a person started with CNC all required tools were provided as well a nice added bonus.I have cut numerous designs with the Machine and it is great for hobbyist or small scale business.Customer support is A+ I reached out to inquire with some questions and they responded promptly without delay and answered all my questions about the product that I had.The only thing I would add is a led light it's not required or needed but to see the fine detail during the cutting process would be a nice addition. Regardless 10 out of 10 from quality to support. I recommend.

【12】

I needed a hobby for the winter and this is it. I have worked around manufacturing for most of my life so I am familiar with machining but this was my first jump into something like this. My journey has just started but I wanted to share a few things that I like about this router and a few things that I learned on the way.Equipment itself- Overall it is heavier than I was expecting - very solid and well built. The components are easily replaceable for any future upgrades or maintenance needed.- The mechanical assembly was very easy. Most of the pieces are prebuilt so it is just attaching the gantry, hang the power supply and screw on the circuit board. One tip is to use a square/right angle to make sure the gantry is perfectly square to the base.- There were no wiring instructions but I went onto YouTube and there are a few videos that show it well. All total it didn't take much time at all to assemble and the wire paths look nice compared to pictures of other similar routers.- Software - There was a thumb drive that came with it but I personally could not get anything to work from it. I went online and downloaded EASEL (Drawing program) and UGS (Sends the program to the router). There is also Candle software (Sends the program to the router) that also seemed to work as well. Two things you need to know is your COM port and your version of windows (64bit vs 32bit). These are all free software, very intuitive and have good videos on YouTube to get started.- Spindle/solid z axis. I'm glad I went with this unit that already has the larger 500W spindle for the extra power. I was comparing this unit to other competitor products and this had the upgrades that you would do anyway. The z axis is solid and has plenty of travel for what I need. I'm mostly cutting 6" wide by 1/2" thick boards but you could do 2" thick material pretty easily. The cutting motion is very solid and smooth. This type of machining is not jerky like a 3D printer.- Customer service. I did have one component that needed to be replaced. I saw it online for $9 but sent an email to Lunyee and they responded the next day and had me running very quickly. Most of the components on this machine can be replaced pretty easily but it is nice to know that there is great customer service available if there is an issue I can't resolve myself.Lessons learned:- The first thing I recommend is to cut a piece of scrap plywood and attach it to the aluminum table. I used the clamps that came with it on a couple projects and the screws scratched the table (Nothing bad but I didn't want to continue it for very long). The plywood allows me to cut out shapes and can be replaced easily.- Learn the masking tape/glue method to hold your wood to the table. This is cheap and it works. No more holes and rough spots on the bed. This made everything work so much better than the clamps.- Dust control. When vacuuming the dust, be careful of the limit switches. They work well and I have set them off mistakenly when trying to clean up during a run. Having to restart a program is a mess so be careful. I don't see the need to invest in a hose attachment or side shields right away. I just use my shop vac every once in a while and that seems to work just fine for this level of work.- Find a supply of flat wood. This is probably the hardest part of the whole process. The wood in the big box stores is mostly bent so you have to be selective. I think that the masking tape/glue process to hold the material helps but a good straight board is important.- Cutting tools. This surprised me but you don't need as much here as I thought. I bought a cheap set that included endmills, ball nose mills and some vcut/engraving bits. I thought I would be breaking them all the time but they have held up well. The only one I broke was dropped on the floor. You don't need to overstock on these as long as you don't start crashing into clamps or mess with the cutting settings (I have lots of time).Pictures:I attached a few pictures to show some of my wins and learning:- Queen of Spades - I worked hard on this one and almost finished before it went bad. I was using a vcut bit to do the outer edge all the way through the wood but the bit was too short. The spindle hit the wood and broke the material free from the clamps. As you can see, it went a little crazy and cut a path right through it. This was my first project with a lot of detail and really enjoyed it.- Cow - this is one of my favorites. I pulled the picture off of a black and white clip art image. I really like how the deep images look with the carving tool.- Einstein - I wanted to try to carve a face and pulled the first black and white picture that came up. It looks great when held at different angles.- Heart sign. This was my last carving using the Easel software. The free pro license only lasts 30 days and then they charge $30/month. I really like how easy Easel was to use so it may be worth the cost. I'm going to transition to the VCarve software which is a one time fee and looks to have quite a bit of additional features for added challenges. You can do a lot with the free software but if you want to carve the fancier projects, plan to spend a little money to get the good software.- Pictures of the wood bed with clamps and tape/glue method. You don't have to worry about hitting a clamp with a spindle with the tape method and you can use the whole surface.I'm having a blast with this router and could go on and on. I'm not going to become a millionaire (Or even dollaraire) from this hobby, but it is fun to make a little projects when it is not nice enough to do much else. Good luck on your adventures.

【13】

Very good price/performance ratio. I wanted the package including the 10W laser kit which was unfortunately not offered on Amazon so I bought the laser and Air-assist from a Lunyee shop on Aliexpress. The combination of the included manual and several good video’s on Youtube (by Lunyee) made the assembly of the machine straight forward. The CNC comes in two main parts easily fitted together. The rest of the work is adding limit-sensors, power-supply, controller(s) and cables. Everything needed for the assembly is included and neatly packaged. I haven’t tried out the offline programming module as I connect the machine via USB (Macbook Pro with M1 running UGS and Openbuilds for the G-Code bit). Candle for Windows and Mac is provided with the machine on a USB stick.